3. Other Artifacts

3.3 Laser Interference


This effect is seen as broad "stripes" in your AFM images, running along the slow scan direction. They are caused by constructive interference between the reflection of the laser from the tip, and the reflection from the sample. See the example below.

Example of laser interference patterns

In the example above, the near-vertical stripe-like oscillations are cause by laser interference.
How to avoid it.

Sometimes this effect is really hard to avoid. It is more noticeable on flat samples, and large (>3 micron) images, and is worse with small, less reflective cantilevers, and it is particularly pronounced on more reflective samples. It's easy to recognise because usually the stripes will be spaced at double the wavelength of the laser used (i.e. usually around 1.3 microns). The best way to avoid this artifact is to re-align the laser, to ensure as little as possible spreads over the edge of the cantilever. Note: Many newer AFMs use a low-coherence laser, and so are much less prone to this problem.

3. Other Artifacts


3.3 Flying Tip


This artifact shows that the AFM is not properly tracking the surface.
In the example below the effect is obvious, but this is not always the case.
Sometimes it is clearer if you look at some of the other signals, like amplitude or phase or deflection images. In the images shown below, note how all the features have a "tail" to their left.

AFM image showing poor feedback

In the example above, the image of nanoparticles shows "tails" on each particle, to the left. The image was recorded scanning from right to left.Typically, the left to right image would show the tails on the right side of each feature. It is typical of this effect that you will get different images in the two directions.

How to avoid it.
If you see this, your feedback parameters are incorrect.
It is usually easy to fix. You generally should increase integral gain, then the proportional gain, you may need to change the setpoint too, or even scan more slowly. See the answer about adjusting AFM feedback parameters here, in in my book.

AFM Artifacts

 

1.1 Tip-sample convolution

 

This is an inherent feature of AFM and can never be fully removed. Any AFM image is a convolution of the shape of the probe, and the shape of the sample. This has the effect of making protruding features appear wide, and holes appear smaller (both narrower and often less deep, too). Broader (less sharp) probes will enhance the effect, as shown below.

 

 

 Illustration of convolution of AFM probe and sample giving rise to the image (red).

 

Probe-sample convolution tends to have the greatest effect on features of similar or smaller radii than the probe. it can be reduced by deconvolution techniques, discussed further in "Atomic Force Microscopy".

 

Where to buy: AFM Probes - Distributors

 

This page lists distributors (as oposed to manufacturers) of AFM and other SPM probes. Currently the list is (very) incomplete.

 

 The book, "Atomic Force Microscopy" by Peter Eaton and Paulbook cover  West was published in March 2010 by OUP.

There is some information about it at this site, but it's somewhat out of date. In particular the contents listing is not quite correct.

 Here is the correct contents of "Atomic Force Microscopy": 

Preface

Chapter 1: Introduction
1.1 Background to AFM
1.2 AFM today

Chapter 2: Instrumental Aspects of AFM
2.1 Basic concepts in AFM instrumentation
2.2 The AFM stage
2.3 AFM electronics
2.4 Acquisition software
2.5 AFM cantilevers and probes
2.6 AFM instrument environment
2.7 Scanning environment

Chapter 3: AFM Modes
3.1 Topographic modes
3.2 Nontopographic modes
3.3 Surface modification

Chapter 4: Measuring AFM Images
4.1 Sample preparation
4.2 Measuring contact mode images
4.3 Measuring intermittent contact mode images
4.4 High-resolution imaging
4.5 Force curves

Chapter 5: Image Processing in AFM
5.1 Processing AFM images
5.2 Displaying AFM images
5.3 Analysing AFM Images

Chapter 6: Image Artifacts in AFM
6.1 Probe artefacts
6.2 Scanner artefacts
6.3 Image processing artefacts
6.4 Vibration noise
6.5 Noise from other sources
6.6 Other artefacts

Chapter 7: Applications of AFM
7.1 AFM applications in materials science
7.2 AFM applications in nanotechnology
7.3 AFM applications in the life sciences
7.4 Industrial AFM applications

Appendix A: AFM Standards

Appendix B: Scanner Calibration and Certification Procedures

Appendix C: Third Party AFM Software

Index

 


 

 

To buy the book, visit Amazon.com

Subcategories